DeWalt DXGNR2700iDF 2,700-Watt Dual-Fuel Portable Inverter Generator with CO-Protect
Who It's Best For: Homeowners seeking dependable 120V/240V split-phase storm backup for essential kitchen, well pump, and central A/C circuits. Why It Stands Out: Compact Dual-Fuel Inverter Architecture: 98cc Generac OHV engine delivering 2,200W running power with CO-Protect safety shutdown. Delivers clean Pure Sine Wave (<3% THD) power with a NEMA 5-20R primary home outlet. Main Trade-Off: Requires a 3/4-inch natural gas hose and a central A/C soft-starter to maximize whole-home performance during peak summer heat.
ReaLoad Lab Rating Breakdown (8.6 / 10)
Every unit is load-bank stress tested at 25%, 50%, 75%, and 100% continuous capacity across Gasoline, Propane, and 7" WC utility Natural Gas. We meter acoustic loudness at 23 feet (dBA), verify 120V/240V sine-wave purity (THD) on a Fluke oscilloscope under central A/C compressor surges, and score value per running watt.
Verified Live Retailer Prices & Stock Comparison
Authorized North American dealers for DeWalt DXGNR2700iDF
Interactive Load Test: What Can This Generator Power?
How It Compares to Other 10,000-Watt Generators
Fuel Usage & Running Cost During an Outage
How Loud Is It in Real Life? (Noise Levels at 7ft, 23ft & 50ft)
At 58 dBA (at 23 ft (standard test)), this generator is as quiet as a normal conversation or central A/C condenser and stays below 55 dBA at a 50-foot neighbor property line.
Control Panel & Outlet Pin Guide
120/240V 50-Amp Heavy-Duty Home Backup & RV Outlet
4-Prong Split-Phase Straight-Blade Outlet. Primary high-output port for 50-amp home breaker interlocks and 50-amp RVs.
Size, Weight & Home Panel Wiring Guide
Ships with floating neutral. Insert NEMA 5-15P bonding plug directly into faceplate receptacle.
What's in the Box & Product Specifications
What's in the Box
Factory contents shipped with DeWalt DXGNR2700iDF
Required to connect the generator safely to your home breaker panel interlock or transfer switch.
Categorized Specifications
How to Connect DeWalt DXGNR2700iDF to Your House
3/4" x 25ft CSA Quick-Connect NG Hose Kit ($119)
0.31" WC drop @ 25ft (175,000 BTU/hr full flow)
50A 50ft 6/3+8/1 AWG Pure Copper Cord ($189)
NEMA 14-50P to SS2-50R Twist-Lock (1.6% Voltage Drop)
Reliance Controls PB50 50A NEMA 3R Inlet Box ($94)
12,500W Continuous Flip-Cover Weatherproof Inlet
Reliance Pro/Tran2 50A Switch / Interlock Kit ($429)
NEC 702 Backfeed Isolation (Floating Neutral)
Micro-Air EasyStart Flex 368 Soft-Starter ($369)
Cuts 3.5-Ton to 5-Ton A/C Startup Surge by 65%
Common Problems & Quick Fixes
Cranks But Won't Start on Natural Gas
Hands-On Video Reviews & Real Owner Consensus
DeWalt DXGNR2700iDF Dual Fuel Inverter Review & Sound Test
Unboxing & Control Panel Callout Inspection
Starts in two pulls on propane after months of storage with zero carburetor gumming or stale gasoline issues.
Delivers pure sine wave power under 3% THD, safely running medical CPAPs, gas furnace circuit boards, and battery chargers.
Runs at 58 dBA from 23 feet, allowing normal conversation without disturbing campsite neighbors or suburban patio gatherings.
The 50.7-pound dry weight and balanced center handle make lifting it into a truck bed or SUV trunk manageable for one person.
Ships with standard 20A duplex plugs rather than a native TT-30R RV plug.
Stock motor surge on 13,500 BTU rooftop air conditioners can trip the 20A inverter overload.
Floating neutral causes modern furnace control boards to lock out with an open ground error code.
The 350 mL crankcase opening sits behind a side panel and easily spills during oil changes.
Verified Owner Reviews (6)
Plugged straight into my Reliance PB50 inlet box and Square D QO interlock. With a Micro-Air EasyStart on our 3.5-Ton Trane, peak startup surge barely hits 62% on Natural Gas.
ReaLoad Engineering Desk Note: Great call swapping the stock Torch F6RTC plug to an NGK BPR7ES gapped at 0.026". Methane has a higher ignition voltage threshold than gasoline, and the copper-core NGK eliminates cold-start hesitation.
My old non-inverter generator caused our home office APC UPS units and Carrier variable-speed blower to fault out. The GM10500XiT holds 60.0 Hz and 2.3% THD rock solid.
Followed the ReaLoad 3-step diagram to pop the lower front cover and remove the white neutral jumper from the ground stud. Runs our 4-Ton A/C (with EasyStart) and pool pump effortlessly.
ReaLoad Engineering Desk Note: Always place a weatherproof label next to the NEMA 14-50R outlet stating "Neutral Unbonded (Floating) for Home Panel Interlock Use" after insulating the white jumper lug.
While neighbors with open-frame generators were burning 15 gallons a day at 78 dBA, our iGen12000TFc ran 15.5 hours per tank and we could sleep right through the night.
Paired with a Flame King dual-tank manifold on two 100-lb propane cylinders. Started our 1/2 HP 240V submersible well pump and kitchen circuits without a flicker.
After dealing with gummed carburetors during winter nor-easters, the fuel-injected EU7000iS starts like a modern car and powers our furnace, well pump, and 2.5-Ton A/C.
Electrical & Technical Q&A (5)
- Your home main breaker panel already bonds Neutral to Ground at the service disconnect.
- Because the GM10500XiT ships with an isolated (Floating) neutral, plugging it into a PB50 inlet box creates zero parallel ground loop.
- If you ever use it standalone at a campsite or jobsite with GFCI cords, plug a $12 NEMA 5-15P Bonding Plug into a 120V outlet.
- Remove the 6 screws on the lower front service cover below the control panel.
- Locate the brass frame ground stud on the right side where the green ground wires and one white neutral jumper wire meet.
- Remove the nut, slide ONLY the white neutral jumper lug off the stud, re-tighten the green ground lugs, and insulate the white lug with heat-shrink or 3M tape.
